Oilfield crane service in Cheyenne & Roger Mills County
Roger Mills County has been one of the most active drilling counties in Oklahoma. If you need a crane on a lease out here, send the details and we'll match you with an operator who works the area.
One of Oklahoma's busiest drilling counties
Roger Mills County lies in the western Anadarko Basin along the Texas line. In 2026 it has consistently ranked near the top of Oklahoma's weekly Baker Hughes county rig counts, tied for the most rigs in the state in some weeks, and it led Oklahoma counties in approved drilling permits over the 12 months through October 2026. Much of the recent drilling targets the Cherokee play.
That activity means steady demand for crane work on new pads: setting tanks and separators for tank batteries, moving pipe and wellsite equipment, and supporting rig-ups and facility construction.
Working out here
Cheyenne, the county seat, is a small town of under 800 people on US Highway 283 and State Highway 47, just south of the Washita River. It's surrounded by the Black Kettle National Grassland, close to the Washita Battlefield National Historic Site, and the Canadian River forms the county's northern border. Roger Mills is one of the least populated counties in the state, so jobs are spread out and reached by lease roads. Give the operator a legal description or GPS pin, notes on road and pad conditions, and any gates or cattle guards.
Most cranes reaching Roger Mills County come from the I-40 towns: Cheyenne is about 29 road miles northwest of Elk City and 23 miles north of Sayre.
Common crane jobs around Roger Mills County
- Tank battery construction: setting oil and water tanks, separators, heater-treaters
- Pipe, flowline and wellsite equipment handling on new pads
- Rig-up and rig move support
- Pumping unit installs as wells go on artificial lift
- Compressor and facility equipment sets
- Ranch and ag lifts: steel barns, equipment and water tanks
Getting a crane to your site
Approximate road distances from Roger Mills County. Mobilization time and travel charges depend on where the operator's crane is parked, so put your exact location in the form.
| To | Approx. road miles | Main route |
|---|---|---|
| Sayre | 23 | US 283 south |
| Elk City | 29 | US 283 / SH 6 |
| Clinton | 58 | US 283 / SH 6 / I-40 |
| Weatherford | 75 | US 283 / SH 6 / I-40 |
Distances are approximate driving distances from OpenStreetMap routing data, rounded.
How it works
- Send the job details. Use the quote form: what you're lifting, how heavy, how high or far, where, and when. No phone call required.
- We match you with a local operator. Your request goes to a vetted crane operator who works the Western Oklahoma area and has equipment suited to the job.
- The operator quotes and confirms. They'll follow up by text or email to confirm the crane size, rigging, site access and price. You decide whether to book.
- The lift gets done. The crane company performs the work under its own insurance, operators and safety program.
Questions
What size crane do I need?
It depends on more than the weight. Crane capacity drops quickly as the load moves farther from the crane, so the operator sizes the crane using the load weight plus rigging, the radius (horizontal distance from the crane to where the load is picked and set), and the height needed. A crane rated at 30 tons can lift far less than 30 tons at a long reach.
As a rough guide: boom trucks and smaller hydraulic cranes are commonly used for lighter, close-in picks such as rooftop HVAC units, hot tubs, trusses and small tanks; larger hydraulic truck or all-terrain cranes are used for heavier tanks, separators, steel and long reaches; wind turbine components need large specialty cranes. The operator will confirm the right machine from their load charts.
What information should I have ready?
- Weight of the heaviest piece (nameplate, spec sheet or bill of lading is best) and its dimensions
- Where it is now and where it needs to go, and the closest spot a crane can set up
- Lift height, and how far from the crane the load must be set
- Ground and access: lease road, gravel pad, soft or muddy ground, gates, slopes
- Overhead power lines, buildings or other obstructions
- Date and time window, plus an on-site contact
- Whether you need rigging, a rigger/signal person, or a truck to haul the load
Photos of the load and the site help a lot. Mention them in the details box and the operator can ask for them when they follow up.
What's the difference between an operated and a bare rental?
An operated (operated & maintained) rental includes the crane plus the crane company's operator, and often a rigger or oiler, usually billed by the hour with a minimum. That's what most one-off jobs use. A bare rental is the machine only: you supply a qualified operator and take on more responsibility for the equipment and the lift. For construction work, OSHA's crane rule (29 CFR 1926 Subpart CC) requires operators to be trained and certified or qualified, so bare rentals are generally a fit only for companies with their own certified operators.
How much notice do you need?
As much as you can give. Availability depends on the operator's schedule and the size of crane needed. Smaller cranes can sometimes be scheduled on short notice; large cranes, multi-crane picks, and jobs that need a lift plan or permits take longer to line up. Put your real deadline in the form and the operator will tell you what's possible.
Local facts on this page: Wikipedia: Cheyenne, Oklahoma · Wikipedia: Roger Mills County · OilAndGasInfo: Roger Mills County wells & permits · CommoVision: Roger Mills rig counts · Berlin Royalties: Cherokee play · OSRM routing